欧美性xxxx极品hdsex-欧美性xxxx极品hd欧美-欧美性xxxx极品高清-欧美性xxxx极品高清3d-a免费毛片在线播放-a免费视频

在濟南標識制作中，有時候會發生這么有一種問題：打印空白處的無規則拉絲體現為時有時無、時長時短的無規律墨道，一般比較粗。下面是針對這個問題總結的產生緣由剖析和處理方法：
In the Ji'nan logo production, and sometimes there will be a problem: the printing blank of the irregular wire drawing is sometimes not, when the long short irregular ink Road, generally relatively coarse. The following is a summary of the problems of the causes of the analysis and processing methods:
1、刮墨刀刃口或刀下面粘有異物能夠在印刷停止過程中前后、上下挪動刮墨刀，擺掉粘著的異物或用一根竹簽直接在刮墨刀刃上剔除(必需由純熟操作工完成，以免因操作不當形成不用要的損失)，必要時需停機對刮墨刀停止徹底清算。
1, scraping knife blade or stuck under the foreign body in the printing process, and can stop in the next move of scraping knife, put off the adhesive or foreign body with a bamboo stick directly in the scraping blade (excluding must complete by skilled operators, in order to avoid improper operation of unnecessary loss, necessary) when you need to stop up completely to stop scraping knife.
2、油墨循環不行有些油墨在墨槽內的死角位置，因得不到杰出循環而構成樹脂分出，構成巨細不一樣的結晶與結塊，或過火枯燥構成外表構成墨皮(夏天簡單發生墨皮，春秋兩季由于氣溫的影響油墨結晶和結塊的狀況較多)，跟著油墨的循環，有一有些油墨結晶或墨皮被轉動的版滾筒帶到刀刃處，刮墨刀將其打碎而構成無規則拉絲。所以有必要從油墨的循環和過濾兩方面進行改善。
2, not some ink in the ink ink circulation groove of the corner position, due to outstanding circulation formed resin separation, crystallization and agglomeration of the same size, or too boring which formed on the surface of skin (summer simple occurrence of ink skin, spring and autumn season two due to the temperature effects of ink crystallization and agglomeration situation more) follow, the ink circulation, there is a version of the drum is rotated or some ink crystallization skin brought to the blade, scraping knife the broken and irregular form drawing. So it is necessary to improve from the two aspects of the cycle of ink and filtration.
(1)循環改善。濟南標識制作辦法一，將墨槽擺布歪斜，確保油墨能夠由稍高的一端寫入，從較低的一端流出，構成杰出的循環;濟南標識制作辦法二，將墨槽平放，但油墨有必要從兩端一起寫入，從中心回流，這么也可構成極好的循環，不可從單邊寫入油墨。
(1) cycle improvement. The method of making a mark in Ji'nan, will be at the mercy of the ink tank to ensure ink skew, written by the end of the slightly higher, the outflow from the lower end, to form a good circulation; Ji'nan logo production to two, the ink tank is flat, but the ink is necessary from both ends to the center, from the back, so also can form excellent the cycle, not from unilateral write ink.
(2)過濾改良。油墨運用前必需停止初次過濾，即便是新墨也要過濾，普通運用140目/英寸的過濾網。油墨在墨槽中循環的過濾工作愈加重要，它能夠很好地過濾掉油墨在運用過程中構成的樹脂結晶和外來雜質，選擇的網目應更細，辦法是在出墨斗的下方套一絲襪，構成一過濾套斗，在過濾一段時間后，假如過濾網被堵，流墨不暢，能夠在套斗的上方用竹簽插一些小洞，增加導墨效果，套斗的下方還能夠起到很好的堆積雜質的作用。
(2) filtration and improvement. Prior to the use of ink must stop the initial filter, even if the new ink also want to filter, the general use of 140 mesh / inch filter. The ink in the ink tank circulation filtering work becomes more and more important, it can filter out a good crystalline resin ink in the course of the formation and the extraneous material selection should be more fine mesh, in a way is the fountain below a silk stockings, a set of filter in the filter bucket, after a period of time, if the filter is blocked, the ink flow is not smooth, can be inserted in small holes in the top set with bamboo bucket, increase the ink guiding effect, set below the bucket can also play a very good role in the accumulation of impurities.
3、油墨疲憊此種狀況多發生在印版著墨面積比較小時。打印過程中，油墨中的樹脂不斷被消耗，假如接連參加溶劑而不增加新墨，樹脂得不到彌補，使油墨各成分的份額發生變化，然后構成油墨疲憊并影響正常運用。恰當增加新墨即可解決問題。
3, tired of this situation occurred in the ink printing ink area is small. In the process of printing, ink resin in the continuous consumption, if successive in solvent rather than adding new ink, resin not to make up, so that the ink components share changes, then tired and affect the normal use of ink. Appropriate to increase the new ink to solve the problem.